Natural gas generator set ESE 160 PSI

Engine

Engine

Model	PSI
Model	8.8 L
No. of cylinders & arrangement	8-in line
Injection system	Turbine with intercooler
Cooling system	With liquid
Maximum standby power (kWm)	117.26
Speed (rpm)	1500
Cylinders (l)	8.8
Inside diameter & stroke (mm)	110,5 x 114.3
Compression factor	9,5 : 1
Regulator	Electronic
Total oil capacity (l)	19
Engine cooling agent capacity (l)	8
Fuel consumption at 100 % prime load (kg/hr) NG/LP	22,58/23.94

Alternator

Alternator

Model	MXB-E 225 LA4 or ECO 165 KW
Frequency (Hz)	50 Hz
Concept	Brushless, 4 poles
Phases	3 + n
Voltage (V)	400 / 230
Insulation class	H
Excitation system	Electronic
Performance	93%
Protection	IP23
Test Certification	EN 10204 : 2001

COMMAND PANEL

Made in metal box, IP54 degree, with lock. The control panel is equipped with the
control ComAp AMF25, equipped with the possibility of starting and stopping the generating set, both in automatic mode and in
electric module. The control module monitors the power grid and can command and control the AAR panel
(automatic reserve release).

Control panel

1. Left button

2. Right button

3. Horn Reset button

4. Fault Reset button

5. Up button

6. Page button

7. Down button

8. Enter button

9. Start button

10. Stop button

11. GCB button. Works in MAN and TEST modes only 12. MCB button. Works in MAN and TEST modes only

12. MCB button. 12. MCB button. Works in MAN and TEST modes only

13. Generator status indicator

14. GCB On. Green LEDs are on if GCB is closed and Gen-set is healthy

15. Load

16. Graphic B/W display, 132 x 64 pixeli

17. Mains status indicator

18. MCB On. The green LEDs are “on” when the MCB is closed and the network is within the preset parameters.

◆ Standard control panel specifications:
The command and control panel is mounted inside the enclosure, in a metal box with IP 54, provided with glass.
for viewing, equipped with:

Control panel

ComAp AMF 25 command module

Static battery charger

Emergency stop button & circuit breaker fuses circuit control

Overcurrent differential protection

Protection relays

Configuration:

1. ComAp AMF25 command module

2. Circuit Breaker protection

3. Locks

4. Alarm

5. START button ON / OFF

6. Hinges

7. Maintenance schedule

8. Metal box

◆ Standard specifications of the control module:

• Microprocessor control
• 132 x 64 pixeli LCD display
• Programming on front panel as well as through PC software
• Control buttons and soft touch navigation
• Remote communication via USB or with optional modules via RS232, RS485, Ethernet or SMS
• Store 180 events with date and time
• Maintenance programming 3 levels
• Engine heater control – optional
• Displays:
  Engine: engine speed; oil pressure; coolant temperature; running time; battery voltage; maintenance date.
  Alternator: voltage (L – L, L – N); current (L1 – L2 – L3); frequency, active power kW, apparent power kVA, reactive power kVA r, power factor, phase sequence.
  Main network: voltage (L – L, L – N); frequency; prepared main network; uncoupled main network; prepared genset; uncoupled genset, , active power kW, apparent power kVA, reactive power kVA r, power factor, phase sequence.
• Warnings:defective battery charging, low battery voltage, failed shutdown, overload, phase reversal, speed sensor fault.
• Alarms: low oil pressure, high engine temperature, under/over temperature, under/overfrequency, under/overvoltage, ECU fault-optional.
• Status displays: missed start, emergency stop, low oil pressure, high engine temperature, under/overload, under/overfrequency, under/overvoltage, oil fault sensor, phase rotation, overload, group overcurrent, phase reversal.
  ◆ Static battery charger: made with TSD technology, high efficiency. Protected for short- circuit currents, it can be used as a current source, input voltage 196-264 V, output voltage 27.6 V / 5A or 13.8 V / 5A.
  ◆ Standards:
  Electrical safety / EMC, BS EN 60950; BS EN 60950 – 6 – 2 EMC; BS EN 61000 – 6 – 4 EMC.

Housing

Made of galvanized steel, painted in electrostatic field, soundproofed. It is modularly designed with
access doors inside on all sides of the generator. The exhaust pipe is a residential type, mounted in
inside the housing.
The housings are designed to optimise cooling of the engine and alternator assembly and can be fitted in
outdoor, providing protection against the weather, and low noise. Painting is carried out
with polyurethane paint with UV protection.

Housing

1. Command module

2. View window

3. Access door for control module

4. Points for crane lifting (optional)

5. Spaces for forklift handling

6. Engine and alternator access door

7. Air intake grills

8. Handles provided with locks

9. Sled type chassis equipped with eyelets

10. Damage button

11. Exhaust gas outlet flap

12. Cable access space

13. Hot air exhaust grille

14. Protective pads